Electronic leak detection
We pressurize the line and walk it with acoustic listening devices and a thermal imaging camera to pinpoint the pinhole before any cutting. This step is what keeps the access opening small and the patch clean.
Licensed, insured, and equipped to find the leak before we cut
Pinhole leak repair Victoria TX that stops the drip for good
When a pinhole leak starts weeping inside a wall or under your slab, the damage climbs fast. Our team delivers pinhole leak repair Victoria TX homeowners call first, using electronic leak detection and thermal imaging to pinpoint the exact spot before we open anything up. We handle pinhole pipe leak repair Victoria Texas wide, from 1920s galvanized lines near Downtown to newer PEX systems out in Vic West. One call, one visit, one dry floor.
Careful work. Honest options.
About this service
What pinhole leak repair Victoria TX actually involves
Pinhole leak repair Victoria TX is a targeted plumbing service that seals or replaces the small, pinhole-sized failure points that form in copper, galvanized, and PEX water lines. A pinhole leak is not a burst pipe. It is a slow, pressurized weep that can spray a fine mist inside a wall cavity for weeks before you notice. We locate it with acoustic listening devices and thermal imaging cameras, isolate the line, then repair or replace the damaged section with new copper, PEX, or a mechanical coupling rated for the pressure.
Most Victoria homeowners call us after a water bill jumps $80 to $200 in a single cycle, or when they spot a warm spot on the floor near the kitchen. If you need pinhole leak repair near me Victoria fast, we run 24/7 emergency calls across Victoria County and can usually be on-site the same day. Left alone, a pinhole leak corrodes the surrounding pipe, saturates the slab, and turns a $400 repair into a $4,000 foundation problem.
- ✓ Stop the water bill bleed
- ✓ Protect the slab and foundation
- ✓ No unnecessary demolition
- ✓ Warrantied repair, not a patch
What's included
What our pinhole leak repair includes
Every pinhole leak repair we do in Victoria includes detection, access, repair, pressure testing, and a written warranty. Here is what is covered on a standard call, and what we quote separately if the job calls for it.
Small access opening
We cut only what we need to reach the failure point, using a concrete saw for slab access or a drywall saw for wall access. Typical openings run 12 to 18 inches, not the multi-foot trenches you see on bad jobs.
Section replacement
The failed section comes out and new copper or PEX goes in, joined with a coupling rated to 150 PSI. We do not clamp over corroded pipe. The repair is meant to last, not to buy time.
Pressure test and verification
Before we close anything up, we pressure test the repaired line at 100 PSI for 15 minutes with a calibrated gauge. If it drops, we keep looking. No repair leaves untested.
Concrete or drywall patch
We patch slab openings with hydraulic concrete mix and re-drywall and texture wall openings. The goal is a floor you can walk on the same day and a wall that paints clean.
Written warranty and photos
You get before-and-after photos of the repair and a written warranty on parts and labor for the repaired section. If the same spot fails, we come back and make it right.
How it works
How our pinhole leak repair process works
You call, we ask three questions: where is the water showing, is the meter spinning with everything off, and how old is the house. That tells us whether to bring slab gear or wall gear. We give you an arrival window on the call, usually 60 to 120 minutes for emergencies.
On site, we pressurize the line and walk it with acoustic listening devices and a FLIR thermal imaging camera. A LeakTronics amplification rig picks up the hiss of the pinhole through slab or drywall. We mark the spot with tape and confirm with a moisture meter before any cutting starts.
We cut a small access opening with a concrete saw or drywall saw, expose the failed section, and shut off the branch. The pinhole section gets cut out and replaced with new copper or PEX, joined with a coupling rated to 150 PSI. Most repairs take 2 to 4 hours from cut to close.
Before we close anything, we pressure test the repaired line at 100 PSI for 15 minutes with a calibrated gauge. If it holds, we move to close-up. If it drops, we keep looking. No repair leaves our hands untested.
We patch concrete with a hydraulic concrete patch mix or re-drywall and texture the opening. Then we walk you through what failed, why, and what the rest of the line looks like. You get photos of the repair and the warranty paperwork before we pull out of the driveway.
STEP 01Phone triage
You call, we ask three questions: where is the water showing, is the meter spinning with everything off, and how old is the house. That tells us whether to bring slab gear or wall gear. We give you an arrival window on the call, usually 60 to 120 minutes for emergencies.
Tools & methods
Tools and methods we use on pinhole leaks
LeakTronics acoustic listening devices
Amplifies the high-frequency hiss of a pressurized pinhole through slab, soil, or drywall so we can narrow the leak to a 6-inch window before cutting.
FLIR thermal imaging cameras
Shows the temperature delta where a hot-water pinhole is weeping inside a wall or under a slab. Confirms the acoustic reading before we open anything up.
RIDGID SeeSnake video inspection cameras
Lets us look inside drain and sewer lines to confirm whether a leak is a pinhole, a joint failure, or a crack before we recommend a repair.
Fluke pressure testing gauges
Calibrated gauges used to pressure-test the repaired line at 100 PSI for 15 minutes. If the line holds, we close. If it drops, we keep looking.
SubSurface Instruments pipe locators
Maps the path of the line under the slab so we know exactly where to cut and where not to. Prevents hitting other utilities during access work.
Milwaukee and RIDGID concrete saws
Cuts clean, controlled slab openings with dust control. Keeps the access opening small and the patch clean so flooring goes back down flat.
Real results
Before and after.
Pinhole Leak Repair
Kitchen slab pinhole in Downtown Victoria
A 1948 bungalow near Downtown Victoria had a water bill jump from $95 to $270 in one cycle. The homeowner noticed a warm spot near the kitchen but no visible water. A previous plumber had quoted a 6-foot slab cut with no detection.
After: We ran acoustic and thermal detection and pinpointed the pinhole to a 10-inch window on the hot-water copper line. Cut a 14-inch access opening, replaced the failed section, pressure-tested at 100 PSI, and patched the slab. Total job time: 4 hours. Bill came in at $780.
Book this service →
Pinhole Leak Repair
Wall pinhole behind bathroom tile in Vic West
A Vic West homeowner noticed bubbling paint and a musty smell on the bathroom wall. A moisture meter read 28 percent in the drywall. The pinhole had been weeping for at least three weeks and had started to affect the framing behind the tile.
After: We located the pinhole with acoustic gear, cut a 12-inch drywall opening, replaced the failed copper section, and pressure-tested the line. The wall was re-drywalled and textured the same visit. Repair cost: $520. Framing was dried and treated before close-up.
Book this service →
Pinhole Leak Repair
Galvanized line replacement in Harris Green
A rental property in Harris Green had three pinhole repairs in 18 months, all on the same galvanized run. The property manager was spending $400 to $700 per repair and losing tenant goodwill with each cut into the floor.
After: We pressure-tested the whole run and recommended replacement over another repair. Replaced 42 feet of galvanized line with new PEX, rerouted around the finished floor, and restored the slab. Total project: 2 days. Cost: $3,400 with a 5-year warranty on the new line.
Book this service → Problems we solve
Pinhole leak problems we solve for Victoria homeowners
Most pinhole calls start with one of these five symptoms. If any of them sound familiar, the leak is already doing damage. Here is what we do about each one.
Ask a pro →Water bill jumped with no change in usage
We isolate the line, run acoustic and thermal detection, and pinpoint the pinhole. Most repairs are done the same day, and we pressure-test the line before we leave so you know the leak is gone.
Warm spot on the floor or a damp patch on the slab
We use a FLIR thermal camera to confirm the hot spot and acoustic gear to hear the leak. Then we cut a small access opening, replace the failed section, and patch the slab with hydraulic concrete mix.
Musty smell or bubbling paint on a wall
We locate the pinhole with electronic detection, cut a small drywall opening, replace the failed section, and pressure-test the line. You get photos of the repair and a patch ready for paint.
Multiple pinholes on the same line
We pressure-test the whole run and give you an honest call on repair versus replacement. If replacement is the right answer, we quote it flat and handle the reroute, slab work, and restoration in one job.
Proof you can check
Licensed, insured, and warrantied
- Master Plumber License · Texas State Board of Plumbing Examiners (TSBPE)
- Journeyman Plumber License · Texas State Board of Plumbing Examiners (TSBPE)
- ICC Certification · International Code Council
- IAPMO Certification · International Association of Plumbing and Mechanical Officials
- Backflow Prevention Assembly Tester Certification · Texas Commission on Environmental Quality (TCEQ) approved program
We locate the pinhole with acoustic and thermal gear, cut a small access opening, remove the failed section, and splice in new copper or PEX with a pressure-rated coupling. The line is then pressure tested at 100 PSI for 15 minutes. Most repairs take 2 to 4 hours. You get photos and warranty paperwork before we leave.
It is a targeted fix for the tiny, pinhole-sized failures that form in pressurized water lines, usually from corrosion or high water pressure. Unlike a burst pipe, a pinhole weeps or mists slowly. We cut out the damaged section and replace it rather than clamping over corroded pipe, so the repair holds long-term.
Typical 2026 pricing in Victoria runs $350 to $1,200 depending on access, pipe material, and whether the leak is in a wall or under the slab. Wall leaks in copper usually land at the low end. Slab access with concrete cutting and patching runs higher. We quote flat before we cut.
Yes. Under-slab pipe corrosion is one of the leading causes of foundation movement in Victoria County. A pinhole that runs for weeks saturates the soil under your slab, causing heave and settlement. Fixing the leak stops the moisture source. If movement has already started, we can refer you to a foundation specialist after the repair.
Ready when you are
Get pinhole leak repair Victoria TX done today
If you have water where it should not be, call us now. We run 24/7 emergency pinhole leak repair Victoria calls, quote flat before we cut, and back every repair with a written warranty. One call gets a licensed technician on the way.
Book a repair 83157330144 →
Request an appointment
Contact SlabFix Repair
Call us at 831-573-30144 any time, day or night. We answer emergency calls 24/7 and schedule standard appointments Monday through Friday. If you're not sure whether you have a slab leak, call anyway and we'll help you figure out the next step.
Call anytime83157330144Email the officeinfo@slableakrepairvictoriatx.com
Office hoursOpen 24 hours · 7 days a week