Full-System Pressure Test
We isolate the house at the main valve and pressure-test the supply system with calibrated gauges. This confirms there is an active leak and rules out fixtures, irrigation, and the water heater before we scan.
Infrared cameras pinpoint hidden slab leaks without tearing up your whole floor
Thermal Imaging Leak Detection Victoria TX that finds the leak before we cut
Thermal imaging leak detection Victoria TX uses infrared cameras to spot the temperature difference a hidden leak leaves under your slab, so we open one small section instead of guessing. If your water bill jumped, a hot spot is creeping across the floor, or you hear water running with everything off, our licensed plumbers find the source fast. We serve homeowners across Victoria County with same-day diagnostics and honest, upfront pricing.
Careful work. Honest options.
About this service
Thermal Imaging Leak Detection Victoria TX Explained
Thermal imaging leak detection is the practice of scanning a floor, wall, or ceiling with an infrared camera and reading the temperature differences that a hidden water leak creates. Warm supply-line water shows as a hot streak; a drain or sewer leak often reads cool. In Victoria TX, where slabs sit on expansive clay soil, that scan is the fastest way to confirm whether the problem is under the slab, in a wall, or at a fixture before anyone picks up a jackhammer.
Most Victoria homeowners call us after one of three things: a water bill that doubled with no change in habits, a warm spot on the tile that never cools, or the sound of running water when every fixture is shut off. Older homes near Downtown Victoria and North Park often have copper pipes under the slab that have thinned into pinhole leaks, while newer builds in Cedar Hill and Shelbourne tend to fail at couplings. Whatever the cause, infrared leak detection Victoria Texas gives you an answer the same day instead of a demolition estimate.
- ✓ Pinpoint Accuracy
- ✓ No Guesswork Demolition
- ✓ Same-Day Answers
- ✓ Works Through Finished Floors
What's included
What Our Thermal Imaging Service Includes
Every scan includes the full diagnostic package, not just a camera walk-through. We pressure-test, scan, confirm with acoustic and moisture gear, and mark the floor. You get a written finding with photos and a repair quote the same visit. Concrete breaking, pipe repair, and patching are quoted separately once we know the scope.
Infrared Camera Scan
We walk every accessible slab surface with a Fluke or FLIR thermal camera, looking for the temperature signature of moving water. The scan covers the whole affected area, not just the room where you noticed the problem.
Acoustic and Moisture Confirmation
Hot spots get verified with a LeakTronics acoustic listening device and a pin-type moisture meter. This step separates real leaks from false positives like sun-warmed slabs or HVAC ductwork running under the floor.
Floor Marking and Written Finding
We tape off the leak location on your floor so you can see exactly where it is, and hand you a written finding with photos and a repair quote. You keep the report whether you hire us for the repair or not.
Repair Quote Same Visit
Because we do the repair work in-house, we can quote the fix on the spot. You get a flat number for the concrete breaking, pipe repair, and patch before we schedule the work.
How it works
How Our Leak Detection Process Works
We ask about your water bill, the meter reading with everything off, and where you have seen moisture or felt heat. That five-minute call usually tells us whether you are dealing with a supply-line leak, a drain leak, or a sewer issue before we ever load the truck.
On arrival we shut the main valve, watch the meter, and pressure-test the system with calibrated gauges. A meter that keeps spinning with the house isolated confirms an active leak. This step takes 15 to 20 minutes and rules out fixtures, irrigation, and water heaters.
We walk the slab with a thermal camera, then verify hot spots with a moisture meter and acoustic listening device. Warm streaks point to hot-water lines, cool patches to drains. We mark the floor with tape so you can see exactly where the problem sits.
For slab leaks we bring in a RIDGID SeeSnake or pipe locator to confirm depth and direction. If the leak is under a wall or behind a cabinet, we adjust the plan. You get a written finding with photos and a repair quote before any concrete is touched.
Once you approve the scope, we open the marked section, repair or reroute the failed pipe, and pressure-test the line before patching. Most slab repairs are finished in one to two days, and we leave the concrete smooth and ready for your flooring.
STEP 01Phone Intake
We ask about your water bill, the meter reading with everything off, and where you have seen moisture or felt heat. That five-minute call usually tells us whether you are dealing with a supply-line leak, a drain leak, or a sewer issue before we ever load the truck.
Tools & methods
Tools and Methods We Use
FLIR Thermal Imaging Camera
Reads surface temperature across floors and walls to reveal the hot or cool signature of a hidden leak. Resolution is fine enough to trace a single supply line under a slab.
Fluke Thermal Camera
Backup and cross-check camera for high-resolution scans. We use it when the leak is small or the slab is thick and the first camera reading is ambiguous.
LeakTronics Acoustic Listening Device
Amplifies the sound of water escaping a pipe so we can confirm the thermal reading and narrow the location to within a few inches.
RIDGID SeeSnake Camera
Video inspection of drain and sewer lines. Confirms whether a cool thermal spot is a drain leak, a blockage, or a collapsed section.
Pressure Testing Gauges
Calibrated gauges that confirm an active leak on the supply system and measure street pressure to check the regulator.
Moisture Meter
Pin-type meter that verifies actual moisture in the slab or subfloor, separating real leaks from false positives like HVAC ducts.
Real results
Before and after.
Thermal Imaging Leak Detection
Pinhole Leak in North Park Bungalow
A homeowner in North Park noticed her water bill had climbed from $90 to $210 over two months. No visible leak, no wet spots. Two plumbers had quoted full-floor demolition to find the problem.
After: We scanned the slab with infrared and found a pinhole leak in the copper under the hallway. One 2-by-3-foot cut, a new coupling, and a pressure test. Total repair time was six hours. Her next water bill was back to $88.
Book this service →
Thermal Imaging Leak Detection
Hot Spot Under Cedar Hill Kitchen Tile
A Cedar Hill family had a warm patch of tile in the kitchen that never cooled. The flooring was starting to lift at the grout lines, and they were worried about a full kitchen remodel.
After: Thermal imaging traced the hot spot to a failed PEX fitting two feet from where they thought the leak was. We cut one square of tile, repaired the fitting, and pressure-tested. The tile was replaced and matched, and the floor is flat again.
Book this service → Thermal Imaging Leak Detection
Emergency Slab Leak in Downtown Victoria Rental
A property manager called at 9 p.m. after a tenant reported water pooling in a Downtown Victoria unit. The main was shut off, but nobody knew where the break was, and the building had four units without water.
After: We responded within the hour, scanned the slab with infrared, and located a burst copper line under the bathroom. We isolated the break, restored water to the other three units that night, and completed the repair the next morning. The tenant was back in the unit by noon.
Book this service → Problems we solve
Hidden Leak Problems We Solve in Victoria
Most slab leaks announce themselves with a bill, a sound, or a wet spot. Here are the ones we see most often and how we handle them.
Ask a pro →Water bill doubled with no change in usage
We shut the main, watch the meter, and pressure-test the system. If the meter keeps spinning, we scan the slab with infrared and confirm the leak with acoustic gear. Most customers get a located leak and a repair quote the same day.
Warm spot on the floor that never cools
We scan the area with a thermal camera, trace the hot-water line, and mark the break. Repair is usually a small cut and a coupling. If the pipe has failed in multiple places, we quote a reroute or replacement.
Sound of running water with all fixtures off
We use acoustic listening devices to hear the leak, then thermal imaging to see it. A RIDGID SeeSnake camera confirms whether it is a supply or drain issue. We quote the repair and get it done, usually within a day or two.
Damp carpet or buckling laminate with no visible source
We scan the slab under the damaged flooring with infrared, confirm with a moisture meter, and locate the source. Repair is scheduled quickly to stop further damage, and we patch the slab so new flooring can go down.
Proof you can check
Licensed, Certified, and Reviewed
- Master Plumber License · Texas State Board of Plumbing Examiners (TSBPE)
- Journeyman Plumber License · Texas State Board of Plumbing Examiners (TSBPE)
- ICC Certification · International Code Council
- IAPMO Certification · International Association of Plumbing and Mechanical Officials
- Backflow Prevention Assembly Tester Certification · Texas Commission on Environmental Quality approved program
An infrared camera reads surface temperature across your floor and shows warm or cool streaks where water is moving under the slab. Hot-water leaks read warm, drain leaks read cool. We confirm each hot spot with a moisture meter and acoustic listening device before marking the floor. The whole scan takes 45 to 90 minutes and does not require pulling up flooring.
Infrared leak detection is the same technology as thermal imaging, just a different name for it. We use a FLIR or Fluke camera to see temperature differences the naked eye cannot, then verify with pressure testing and pipe locators. It is the fastest way to find a hidden leak in Victoria without tearing up your whole floor.
A standard residential scan runs $250 to $450 in 2026, depending on square footage and how many rooms we need to check. If we find the leak and you hire us for the repair, we credit the detection fee toward the job. Emergency after-hours scans run higher. You get the exact number before we start.
Yes. Slab leaks are exactly what thermal imaging is best at. The camera sees the temperature signature of water moving under concrete, and we confirm with pressure testing and acoustic gear. In Victoria's clay soil, slabs shift and shear pipes, so we scan the whole affected area, not just the spot you noticed.
Ready when you are
Book Thermal Imaging Leak Detection Victoria TX Today
If your water bill is climbing or you feel a warm spot on the floor, call us now. We are licensed, insured, and we quote the price before we start. Same-day scans are usually available, and emergency service runs 24/7.
Book a Scan 83157330144 →
Request an appointment
Contact SlabFix Repair
Call us at 831-573-30144 any time, day or night. We answer emergency calls 24/7 and schedule standard appointments Monday through Friday. If you're not sure whether you have a slab leak, call anyway and we'll help you figure out the next step.
Call anytime83157330144Email the officeinfo@slableakrepairvictoriatx.com
Office hoursOpen 24 hours · 7 days a week